Category: Software Platform

Wireless Activity Detection Sensor

IoT Wireless Activity Detection Sensor Product Manual

Features Industrial Grade Sensor with 3-axis Accelerometer for Activity Detection Configurable Activity Detection Parameters Uses Interrupts for Activity detection with little power consumption Configurable Acceleration Range ±2g to ±16g Configurable Interrupt Threshold ±16mg to ±15.3g Configurable Data Rate 1Hz to 5.37KHz Configurable Interrupt Duration 200us to 1sec Customizable Interrupt Types and Combinations for generating Activity condition Configurable In-built Interrupt disable time for maximizing battery life time (sends a packet after this interval to show activity detection enabled) Operating Temperature Range -40 to +85 °C Superior LOS Range of up to 28 miles with 900MHz High-Gain Antennas Interface to Raspberry Pi,

Read More »

IoT Wireless Asset Monitor Product Manual

Features Industrial Grade Sensor with 3-axis Accelerometer for Asset Monitoring Configurable Asset Monitoring Parameters Uses Interrupts to keep track of Assets with little power consumption Configurable Acceleration Range ±2g to ±16g Configurable Interrupt Threshold ±16mg to ±15.3g Configurable Data Rate 1Hz to 5.37KHz Configurable Interrupt Duration 200us to 1sec Customizable Interrupt Types and Combinations for generating Monitoring condition Configurable In-built Interrupt disable time for maximizing battery life time Operating Temperature Range -40 to +85 °C Superior LOS Range of up to 28 miles with 900MHz High-Gain Antennas Interface to Raspberry Pi, Microsoft Azure, Arduino and More Example Software for Visual

Read More »
Node-Red Dashboard

Node-RED and the Wireless Enterprise Line

Code-Free Programming If you’ve been following our recent forays into the latest of IoT, you are probably already familiar with Node-Red. If you haven’t, you’re in for a treat! In short, Node-Red is a visual flow builder that was developed with IoT in mind, you can think of it as a way to build a program without actually writing any code. In this article, we’re going to focus on our node-red-wireless package that we use to integrate our Wireless Enterprise Line into this amazing framework. If you are new to our Enterprise line of Wireless Sensors, check out the intro

Read More »

Using Node Red to Control the PCA9536

GPIO in minutes If you haven’t already, make sure to go through the setup tutorial. Once you’ve finished that we’re ready to go! The PCA9536 is an 8-pin CMOS device that provides 4 bits of General Purpose parallel Input/Output (GPIO) expansion through the I2C bus. We manufacture multiple mini-modules that utilize this chip, you can check them out here. If you haven’t already, get your devices plugged in, on a Raspberry Pi, that means installing the adapter, hooking up the I2C cable to the In port on the Relay Board, and powering the board. On any platform without native I2C,

Read More »

IoT Wireless Current Monitor Product Manual

Features Industrial Grade Wireless Current Monitor (RMS output) Range 0-100A Auto Time Delay based data sample transmission or on current change detection (configurable duration in both cases) Configurable Current change detection bounds Configurable Current Sensor Calibration over the wireless link 1-Mile Range with 2.4GHz or 2 Mile Range with 900MHz On-Board Antenna Superior LOS Range of up to 28 miles with 900MHz High-Gain Antennas Interface to Raspberry Pi, Microsoft Azure, Arduino and More Example Software for Visual Studio and LabVIEW Wireless Mesh Networking using DigiMesh® 256 Sensor Nodes per Network Open Communication Protocol for custom interfacing applications Small Form Factor

Read More »
Industrial wireless sensors

Long Range IoT Wireless Sensor FAQ

Wireless Sensor FAQ General Frequently asked questions How do I know if this Wireless sensor is working if there is no power light on it? We didn’t add a power led to save power, you can hit the reset button on the sensor and it will send two data packets. First data packet will indicate that the sensor is in run mode and the second data packet will contain all the sensor info, device info and sensor readings. You can find more about this in the product manual. What is the Zigmo/Wireless Router and why do I need it? Zigmo

Read More »
wireless digital input controller

Long Range IoT Wireless 7 Channel Push Notification Sensor Product Manual

Features Industrial Grade Sensor with µs latency Sleeps when no push input detected Detects up to 7 Inputs in parallel Can be used as Push Notification or Digital Input 2 Analog Inputs measurement 2 Mile Range with On-Board Antenna Superior LOS Range of up to 28 miles with High-Gain Antennas Interface to Raspberry Pi, Microsoft Azure, Arduino and More Example Software for Visual Studio and LabVIEW Wireless Mesh Networking using DigiMesh® 256 Sensor Nod e per Network Open Communication Protocol for custom interfacing applications Small Form Factor Wireless Sensor (3×3 inch) Two modes of Operation Configuration mode for Sensor and

Read More »
Wireless Vibration Sensor

IoT Wireless Vibration Sensor Product Manual

OverviewFeaturesApplicationsDescriptionGetting StartedResources RequiredStepsTroubleshootingChanged/Unknown setting at sensor endChanged/Unknown setting at PC endModes of OperationMode Selection ProcessFrame Communication at Power upRun ModeConfiguration ModeAppendix AConfiguration Commands1. Set Broadcast Transmission2. Set ID and Delay3. Set Destination Address4. Set Power5. Set PANID6. Set Retries7. Read Delay8. Read Power9. Read Retries10. Read Destination Address11. Read PANID12. Enable Encryption13. Disable Encryption14. Set Encryption KeyAppendix BFrame Checksum CalculationOverview Features Industrial Grade 3-axis Vibration Sensor with RMS, MAX and MIN acceleration in g Vibration Range ±16g Noise Removal using Low pass filter Frequency Range 0.1 to 408 Hz (Bandwidth: 408 Hz) Sampling Rate up to 952 Hz Builtin Offset

Read More »
Wireless Accelereo Gyro Magneto Sensor

Long Range IoT Wireless Accelerometer Gyroscope Magneto Temperature Sensor Product Manual

Features Industrial Grade Sensor with 3-axis Acceleration, 3-axis Angular Rate, 3-axis Magnetic Gauss and Temperature Output Acceleration Range up to ±16g Configurable Acceleration Resolution 0.061 to 0.732mg Angular Rate Range up to  ±2000dps Configurable Angular Rate Resolution 8.75 to 70dps Magnetic gauss Range up to ±16gauss Configurable Magnetometer Resolution 0.14 to 0.58mgauss Operating Temperature Range -40 to +85 °C 2 Mile Range with On-Board Antenna Superior LOS Range of up to 28 miles with High-Gain Antennas Interface to Raspberry Pi, Microsoft Azure, Arduino and More Example Software for Visual Studio and LabVIEW Wireless Mesh Networking using DigiMesh® 256 Sensor Nod

Read More »
wireless proximity light sensor

Long Range IoT Wireless Proximity Sensor Product Manual

Features Industrial Grade Wireless Proximity and Ambient Light Sensor with 16 bit resolution Proximity distance up to 200mm Proximity Data update rate 32.25 measurements/sec Proximity IR Led current 160mA Ambient Light Range 0.25 to 16k lux Ambient Light Sample Update rate of 3 samples/sec Auto sample transmission on Proximity or Ambient Light change detection periodically (configurable duration in both cases) Configurable Proximity or Ambient Light change detection percentage 2 Mile Range with On-Board Antenna Superior LOS Range of up to 28 miles with High-Gain Antennas Interface to Raspberry Pi, Microsoft Azure, Arduino and More Example Software for Visual Studio and

Read More »