Author: Bhaskar

Wireless IoT Soil Moisture Temperature Conductivity Sensor Product Manual

NCD’s Long Range Industrial IoT Wireless Soil Moisture Temperature EC SensorFeaturesApplicationsDescriptionGetting StartedResources RequiredStepsTroubleshootingChanged/Unknown setting at sensor endChanged/Unknown setting at PC endModes of OperationMode Selection ProcessFrame Communication at Power upRun ModeConfiguration ModeAppendix AConfiguration Commands1. Set Broadcast Transmission2. Set ID and Delay3. Set Destination Address4. Set Power5. Set PANID6. Set Retries7. Read Delay8. Read Power9. Read Retries10. Read Destination Address11. Read PANID12. Enable Encryption13. Disable Encryption14. Set Encryption Key15. Sensor Soil Moisture Calibration16. Sensor Soil Temperature Calibration17. Sensor Soil EC Calibration19. Super CommandAppendix BFrame Checksum CalculationNCD’s Long Range Industrial IoT Wireless Soil Moisture Temperature EC Sensor Features Wireless Soil Moisture Temperature EC

Read More »

Wireless IoT PAR Sensor Product Manual

NCD’s Long Range Industrial IoT Wireless PAR SensorFeaturesApplicationsDescriptionGetting StartedResources RequiredStepsTroubleshootingChanged/Unknown setting at sensor endChanged/Unknown setting at PC endModes of OperationMode Selection ProcessFrame Communication at Power upRun ModeConfiguration ModeAppendix AConfiguration Commands1. Set Broadcast Transmission2. Set ID and Delay3. Set Destination Address4. Set Power5. Set PANID6. Set Retries7. Read Delay8. Read Power9. Read Retries10. Read Destination Address11. Read PANID12. Enable Encryption13. Disable Encryption14. Set Encryption Key15. Sensor PAR Calibration16. Super CommandAppendix BFrame Checksum CalculationNCD’s Long Range Industrial IoT Wireless PAR Sensor Features Photosynthetically Active Radiation Sensor PAR Sensor Measurement Accuracy ±2%FS Measurement Range 0-2000 um/m^*s Spectral Range 400-700nm Aluminum alloy housing Cosine

Read More »

IoT 4-20mA signal Splitter Product Manual

NCD’s Long Range Industrial IoT Wireless 4-20mA Current Signal Splitter Features Industrial Grade 1-Channel 4-20mA Current Input Industrial Grade 1-Channel 4-20mA Isolated Current Output Input Range 0-20mA with 15-bit Resolution Output Accuracy ± 0.05 FS Converts 4-20mA devices into Wireless Nodes 2 Mile Line-of-Sight Range with On-Board Antenna Superior LOS Range of up to 28 Miles with High-Gain Antennas Interface to Raspberry Pi, Microsoft® Azure®, Arduino and More Example Software for Visual Studio Wireless Mesh Networking using DigiMesh® Open Communication Protocol for Easy Software Integration Validates and Retries Lost Communication Packets Overview Introducing NCD’s Long Range Wireless 4-20mA Current Splitter

Read More »

Wireless RTD sensor with node red

Getting started with node red and RTD In this article we will learn how to install and setup node red. install node jshttps://nodejs.org/en/ install NVMhttps://github.com/coreybutler/nvm-windows/releases open command line and switch to node js 12.20.2nvm install 12.20.2nvm use 12.20.2 install node red npm install -g –unsafe-perm node-red Checkout this article for more info How to install node red lib start node redcommand — node-red open a web browser and enter this http://127.0.0.1:1880/ click manage palette and search for ncd-red-wireless install ncd-red-wireless install node-red-dashboard   Build node red flow There are tons of examples and tutorials available on how to build flows. In

Read More »

Wireless IoT Dissolved Oxygen DO and Temperature Sensor Product Manual

NCD’s Long Range Industrial IoT Wireless pH ORP Temperature SensorFeaturesApplicationsDescriptionGetting StartedResources RequiredStepsTroubleshootingChanged/Unknown setting at sensor endChanged/Unknown setting at PC endModes of OperationMode Selection ProcessFrame Communication at Power upRun ModeConfiguration ModeAppendix AConfiguration Commands1. Set Broadcast Transmission2. Set ID and Delay3. Set Destination Address4. Set Power5. Set PANID6. Set Retries7. Read Delay8. Read Power9. Read Retries10. Read Destination Address11. Read PANID12. Enable Encryption13. Disable Encryption14. Set Encryption Key15. Sensor DO Calibration18. On Demand Data19. Super CommandAppendix BFrame Checksum CalculationNCD’s Long Range Industrial IoT Wireless pH ORP Temperature Sensor Features Industrial Grade Wireless Dissolved Oxygen DO and Temperature Sensor DO Measurement Accuracy ±2%FS

Read More »

RS485 Configuration

How To Configure Wireless To RS485 Converter Step 1 . In order to perform configuration you will need a USB modem . we recommend this modem. Step 2. Download the configuration utility. This utility will need labview run time driver and serial driver. A. Run time driver B. Serial Visa Driver Step 3. Open the ui and select sensor configuration. During this step make sure you are selecting correct serial port. The serial port baudate should be selected as 115200. Step 4. Put RS485 modem in configure mode by Press release RST button and immediately press and hold CFG button

Read More »

How to Activate Verizon IoT Sim Card

How to Activate Verizon IoT SIM card NCD’s IoT Edge Computer supports various SIM cards from multiple companies. So far, we have tested the IoT Edge Computer with Verizon and Hologram SIM cards. Use this guide to set up your Verizon SIM card. 1. Go To ThingSpace ThingSpace is the Verizon IoT center. This is where you can purchase SIM cards, activate them, and find any other information related to Verizon SIM cards. Go to ThingSpace. You will need to create an account there. 2. Activate SIM Card Follow steps 2.1 – 2.6 to activate a SIM Card for Verizon. 1. In order to activate a

Read More »

Industrial Modbus RTU Modem

Industrial Wireless RS485 ModBus RTU Modem User Guide ModBus protocol is one of the most robust and widely used industrial communication protocols. Most all industrial computer, PLC, and SCADA systems supports this protocol. These systems are responsible for controlling and making decisions on a factory floor. Using the ncd.io Industrial Wireless RS485 ModBus RTU Modem, the factory floor systems like PLC and SCADA can read sensor data and make quick intelligent decisions.    How It Works This Wireless ModBus RTU Modem is an extremely simple device. When a sensor transmits data, this modem captures the data and stores it in

Read More »

How to Upload a Web UI to the NCD5500 Ethernet Module

NCD5500 Version Identification Step 1 — Download ncd Ethernet config utility and web interface page The ncd ethernet config utility can be used to change Ethernet module settings, upload new firmware or to uploaded web ui. web interface Download  Step 2 — Connect the Ethernet Module and power it up Once the Ethernet module is connected , open the config utility. It will look something like this. MAKE SURE you have the latest version of software.  In the upper left corner, it will say V1.0.7 or later. Open the Mac Address of the device and make sure the latest firmware

Read More »